Bộ lưu điện PMI 100 -200kva

0₫

Công suất: 100 -200kva

Xuất xứ: Thổ Nhĩ Kỳ

Mô tả sản phẩm
Thông số kỹ thuật
Catalog
Binh luận

Mô tả sản phẩm

Thông số kỹ thuật

GENERAL
Power Range	1-1 PHASE/ 1, 2, 3, 4, 5, 6, 7.5, 10, 15, 20 KVA 3-1 PHASE / 10, 15, 20, 30, 40, 60 KVA 3-3 PHASE / 10, 15, 20, 30, 40, 60, 80, 100, 125,150, 200 KVA"
Topology	Double Conversion Online System with Output Isolation Transformer
Control	Microprocessor Controlled System
RECTIFIER
Topology	Full Bridge Phase Angle Controlled Thyristor Module Rectifier (6 Pulse / 12 Pulse Options)
Control	Microprocessor Controlled System
Nominal Input Voltage	110 VAC / 220 VAC / 230 VAC / 240 VAC / 380 VAC / 400 VAC / 415 VAC / 480 VAC ±15%
Nominal Input Frequency	50 hz. ±5% or 60 hz. ±5%
Input Power Factor	>0.8 Inductive (>0.9 with 12 Pulse Rectifier)
Nominal DC Voltage	110 VDC / 125 VDC / 144 VDC / 220 VDC / 264 VDC / 360 VDC
Nominal DC Current	Available upto 1200 Amp (12 Pulse over 400 Amp)
Static Tolerance	<1%
Output Voltage Ripple RMS	<1% (at full load)
Input Isolation Transformer	Galvanically Isolated (optional)
Serial Dropper Diodes	Optional depending on DC load input voltage range
Total harmonic Distortion (ThDi)	<30% (standard); <10% (with 12 Pulse Rectifier)
Battery Charging Principle	Constant Current Constant Voltage
Battery Charging Current Range	0-20 Adjustable based on Battery Current (standard); Can be higher based on Battery Capacity
Float Charge Voltage	100% to 115% of Floating Output Voltage Programmable
Boost Charge Voltage	100% to 125% of Floating Output Voltage Programmable
Boost voltage (V/C)	2,4 lead acid battery 1,55 NiCd Battery
Float voltage (V/C)	2,23 lead acid battery 1,40 NiCd battery
Equalize voltage (V/C)	2,7 lead acid battery 1,7 NiCd battery with reduced current
Front Panel Measured Values	LCD Display for Load Output Voltage / Current , Battery Output Voltage / Current and Line Voltage / Line Current / Frequency
Alarm Contacts (1 Open 1 Closed)	Open or closed; rectifier failure, over voltage, low battery, over temperature, line failure, Input MCB, Load MCB, Battery MCB
Front Panel Indicators	Float mode, Boost mode, Current mode, Boost inhibit, Battery ending, Low battery, Battery test failure, Line failure, Fan failure, Over voltage, Under voltage, Over temperature, Rectifier failure, SCR fuse failure (LED indication), Line MCB (LED indication), Load MCB (LED indication), Battery MCB (LED indication)
Front Panel Set Menu	Boost charge voltage, Float charge voltage, Low battery voltage , Battery test , Charger output current, Battery charge current, Battery automatic boost current and float current, Auto & Manual boost selection, Manual boost time, LED test and On - OFF.
Event History	Last 250 events recorded and displayed on front panel and on PC via RS 485
Communication	RS 485 - Timer Setting, Boost Voltage Setting, Float Voltage Setting ,Output current setting, battery current setting , automatic boost setting and Reset buttons.
Protections	Input: Thermic-Magnetic Over Current Protection, Over Voltage Protection, Phase Sequence Free Operation (3 Phase), Soft Start
	Output: Short Circuit Protection, Over Voltage Protection, Reverse Voltage Protection
	Battery: L-C filters, Overcurrent Electronic protection,Over Voltage Protection and Thermic Fuse
INVERTER
Topology	3 Full Bridge 6 high Frequency IGBT Inverter Modules (3 Phase); 1 Full Bridge 2 high Frequency IGBT Inverter Modules (1 Phase)
Power Factor	0.8
Nominal Input Voltage	110 VDC / 125 VDC / 144 VDC / 220 VDC / 264 VDC / 360 VDC
Operating Input Voltage	±15%
Nominal Output Voltage	110 VAC / 220 VAC / 230 VAC / 240 VAC / 380 VAC / 400 VAC / 415 VAC / 480 VAC
Voltage Tolerance	static ± 1% dynamic with 100% load change ± 10% in 100 msec.
Overload	at 125% Load 10 minutes at 150% Load 1 minute at 300% Load 1 second
Waveform	Pure Sinusoidal
Total Harmonic Distortion (ThDv)	at Linear Load < 3% at Non-Linear Load < 7%
Crest Factor	3 : 1 (1 second)
Regulation time	40 msec into ±2%
Angle Deviation / Static Tolerance Deviation	symmetric load - - < 1° / <1% 50% asymmetric load - - < 1° / <1% 100% asymmetric load - - < 1° / <1%
Nominal Output Frequency	while synchronized with the line 50 hz ±2% or 60 hz ±2% while not synchronized with the line 50 hz ± 0.1% or 60 hz ± 0.1%
Switching Frequency	20 Khz.
Efficiency with Nominal Load	>85% / >90% depending on DC Bus Voltage
Isolation Transformer	Galvanically Isolated (standard)
Short-circuit behaviour	3 x Nominal Output Current
Protection	Short Circuit Protection, Over Voltage Protection, Under Voltage Protection, Over Current Protection and Over Temperature Protection
Paralleling	Parallel Redundant (Hot Standby) with Static Transfer Switch Unit (optional)
Communication	RS 485
Front Panel Warnings	Inverter Failure, Inverter Output High / Low, Inverter DC Voltage High, Inverter Overtemperature, Inverter not Synchronized, Bypass out of Limit, Low Battery / Low DC Input, Inverter Overload, Internal Overtemperature / Fan Failure, Bypass MCB OFF, Output MCB OFF IGBT SCR Fuse Failure, Maintenance Bypass On, Backfeed Protection Failure
Front Panel Set Menu	Cold Start ON / OFF, Automatic Start ON / OFF, ECO Mode ON / OFF, Automatic Retransfer Bypass Inhibit, DC Cut off Low Battery Level Output Adjustment, Bypass Voltage Tolerance Adjustment, Synchronization Frequency Adjustment, DC Cut off High Voltage Level
Alarm Contacts (1 Open 1 Closed)	Inverter Failure, Inverter Overtemperature, Inverter Overload, Load on Bypass / Inverter, Bypass out of Limit, Inverter not Synchronized, Low Battery / Low DC Input, High DC Input
STATIC TRANSFER SWITCH
Topology	Thyristor controlled transfer switch
Nominal Voltage	110 VAC / 220 VAC / 230 VAC / 240 VAC / 380 VAC / 400 VAC / 415 VAC / 480 VAC ±10%
Nominal Frequency	50 Hz or 60 Hz
Operational Current	50 A / 100 A / 200 A – 1 Phase; 3x50 A /3x100 A /3x200 A /3x 300 A-3 Phase
Operation Voltage Interval	± 10% Adjustable
Synchronization Interval	± 10% Adjustable
Frequency Interval	± 10% Adjustable
Load Power Factor	0,7 – 1 Inductive
Overloading Capacity	Between 100% - 125% 10 min. Between %125 - 150% 5 sec. Between %150 - 300% 100 msec.
Transfer Management	Break before make
Synchronous Transfer Time	< 5 msec. ( ¼ cycle at 50 Hz)
Asynchronous Transfer Time	< 11 msec.
Other Controlled Transfers	0 msec.
Efficiency	>99%
Communication	RS 485
Protection	Over temperature Protection, Thermal Fuse Protection at Source Inputs , Overvoltage Protection at Source Inputs
Front Panel Indications and Warnings	Synchronization Failure (Light), Asynchronous Transfer Enabled (Light), Prioritized Source Preference (Light), Input Source Fault (Light and Sound), Over current (Light and Sound), Over temperature (Light and Sound), Thyristor Failure (Light and Sound)
Buttons	"Asynchronous Transfer Enable" Button, "Manual Transfer Enable" Button, " Reset" Button, "Source 1 or Source 2 Preferred" Button
Manuel Bypass	0 (Off) / 1 (1st Source) / 2 (STS Output) / 3 (2nd Source) Selector Switch
STATIC BY-PASS
Topology	Uninterruptible static switch with back-feed protection
Bypass System	No break semiconductor thyristor
Nominal Voltage	110 VAC / 220 VAC / 230 VAC / 240 VAC / 380 VAC / 400 VAC / 415 VAC / 480 VAC ±10%
Nominal Frequency	50 hz ± 2% or 60 hz ± 2%
Load Level	300%
Bypass Isolation Transformer	Galvanically Isolated (optional)
Voltage Stabilizer	Servo or Static Controlled with front panel (optional)
Inverter/Bypass transfer time	Inverter failure Max. 5 msec. Overload or manual transfer 0 msec.
Bypass/Inverter transfer time	0 msec.
Efficiency	>99%
Voltage Tolerance	± 10%
SAFETY
Over Voltage Protection	IEEE 587 4500 A, 110 Joules (standard), 40 kA 1000 joules surge arrestor (optional)
Electrical Interference Reduction	FCC Part 15 Class B
Electrical Standards	EN 50091-1 (Security) / EN 50091-2 (EMC)
Protection Level / Color	IP 20 / RAL7035, available upto IP52
MTBF	100,000 hrs. (w/out battery group)
Enclosure Material	Mild Steel, Zinc-phosphate coated; 100 μm electrostatic paint; 1.5 mm thickness
Panel Lighting	Optional
Cooling	Forced fans with redundant fans (optional natural cooling)
Cable Entry	Bottom (optional top entry)
Distribution	AC and DC available on request
Output Connections	1 Ph 2W, 3 Ph 3W, 3Ph 4 W
Dimensions	Range of options available and vary based on customized configuration
Operating Temperature	-10 / +50 °C
Relative humidity	5 - 90 %
Operating Altitude	Max. 2000 Mt.
Noise Level	Max. 60 db